GSX-R1000 First Engine Startup

After much debugging of the electrical and fuel injection systems, we have ignition!

We Have Ignition

Click to watch the video on Youtube

Advertisements

Plumbing the Oil Cooler

Oil Cooler

Setrab oil cooler plumbing.

The Suzuki GSX-R1000 engine comes with an oil cooler, but has short hoses as the cooler is mounted right in front of the engine. I cut off the flexible hose section from the tube and flange that mounts to the engine on each OEM hose assembly. I then purchased stainless steel AN-10 bung fittings and turned them on the lathe to fit over the OEM pipes. These were then welded together. The welding was smooth as butter because the metal types matched well. I then made up a pair of hoses to run from those fittings over to the oil cooler and back.

Youtube Update 9: Debugging the Engine & Electrical System

OK, time to get caught up on blog posts. Experience the agony of defeat and the joy of victory along with me as I debug the electrical system one fault at a time, prepare the engine for starting, and debug the engine. GSX-R1000 engines have a sensor that looks for the original ignition switch, and won’t start without it. This had to be worked around, followed by a determination that all the fuel injectors were clogged. I then made a device to clean and test the fuel injectors…

Click the photo to watch the video on Youtube.

Oil Filling

Ready to fill the engine with oil, coolant, and gasoline.

Youtube Video Update 7

Here’s another video I uploaded to Youtube a while ago. This one shows test fitting the headers outside the car, installing the engine & headers, then removing the headers with the engine in the car. The first version of the headers shown here both touched the firewall and would have needed to be removed before the oil filter could be changed, which was decidedly non-optimal. When I pointed this out to the header fabricator, he went back and built a completely new set at no extra charge.

Test fitting the headers, on Youtube

Headers

Headers, version 1.0, installed on the GSX-R1000 engine.

How to Install a Low-Profile Oil Pan on a 2007-2008 K7 GSX-R1000 Engine

Installed

Low-profile bike-engined car or motorcycle-engine car billet aluminum oil pan installed on a 2007-2008 K7 Suzuki GSX-R1000 engine

When building a motorcycle-engine car, the oil pan has to be replaced with a flat-bottomed pan. This allows the engine to sit flat on the floor pan of the car, lowering the center of gravity. Also, the g-forces experienced by a car engine are completely different from those seen by a motorcycle engine. When a motorcycle corners the forces are still straight down through the centerline of the engine, whereas when a car corners the force pushes the oil to the side of the engine. Through sad experience this was found to make the engines explode. A proper flat-bottomed oil pan has a separate compartment for the oil pickup, connected to the rest of the pan by one-way flappy doors that keep the oil near the pickup during cornering and braking. Note that some flat-bottomed oil pans are made for stunt motorcycle riding and so use a swiveling oil pickup. The car-racing guys don’t have enough experience with these, so don’t use them. Your engine may explode, and this would be bad.

As it seems no one on the Internet has ever explained how to install such an oil pan before, so here it is. My oil pan arrived without even a word of explanation, yet the operation detailed here is fairly important. As in, your engine is toast if you try to start it without doing this. Now that the Thai government has prohibited importation of all used motorcycle parts, my engine is now completely irreplaceable.  So that would be bad.

2006 and earlier GSX-R1000 models had the oil pressure relief valve sandwiched between the engine block and the oil pan. In 2007 Suzuki moved the valve to a new housing closer to the center of the oil pan, connected by a passageway to the original location. In the original location they replaced the valve with a simple cylindrical connector gizmo with o-rings at each end so that oil would still flow to the new valve location. This gizmo is popped out by hand and discarded, and the oil pressure relief valve is flipped top for bottom and inserted in its place. This should become clearer in the photos below.

As I’d really like it if my engine didn’t leak, I’ve used Permatex gasket sealant on all sealing surfaces and around the heads of the oil pan mounting bolts. The original oil pan used special gasket washers under the mounting bolts that had fallen by the wayside at some time in the past, leaving my engine with just two out of fourteen. Since I couldn’t find these anywhere on the Internet outside of a complete engine-rebuild gasket set, I sourced 6mm copper crush washers in their place along with new 6mm x 40mm socket head cap screws as the original ones won’t work with the new oil pan. Has to be socket-head cap screws; hex head bolts will just sit on the outside of the oil pan as their head won’t fit into the counterbores in the oil pan. Needless to say, all this required many trips to the hardware store and much Internet research. You’re welcome.

UPDATE: A tip of the hat to the guys on ApexSpeed.com, in particular Gary Hickman of Edge Engineering, who jumped right in with all the know-how and history to figure out what’s going on here. You can see (and buy) the latest version of these oil pans here: EdgeCNC.com .